Note that the screen blanks if the battery is discharged completely. This timer is equipped with a rechargeable Ni-Mh battery which will protect your programs during power failure for up to 30 days. Always use a non-metallic object such as a wooden pencil. For example if the current time is 2:00PM and you just programmed the unit to turn ON at 1:00PM, you will need to press the manual override key to turn it ON.Thereafter, the unit will resume normal operation (automatic).ĭo not use a metallic object to adjust this timer. When you initially program the unit it may be necessary to press the manual override key as the unit will not look back to determine if it should be ON. Pressing the door will override the timer setting and will manually turn the switch ON and OFF. Then press the “PROG” key in order to delete this particular program.ġ20VAC 60Hz 15A Resistive 15ATungsten 1HP Then press the “HOUR” and “MIN” keys until -:- is displayed. To delete a particular program simply press the “PROG” key until the desired program is displayed.Ģ. When complete press the “CLOCK” key to return to current time and day.ġ. Any program can be edited by pressing the “HOUR”,“MIN”, and “DAY” keys.Then press the “PROG” key in order to accept the changes.ģ. Each time you do this you will be able to scroll thru the programs.Ģ. To review the programs that have been entered, press and release the “PROG” key. The “TIMER” symbol will no longer be on the display.ġ. To de-activate press the “DAY” and “HOUR” keys at the same time again. Once activated the “TIMER” symbol will be blinking.Ģ. To activate press the “DAY” and “HOUR” keys at the same time. This function will only operate if one or more programmed switching commands are set.ġ. This feature sets the timer to switch lights ON and OFF at random intervals while you are out of the house. The “DST” will no-longer be on the screen. To de-activate DST press the “HOUR” and “MIN” keys at the same time. The present time will increase by an hour and the screen willĢ. To activate DST press both of the “HOUR” and “MIN” keys at the same time. To change the day selection simply keep pressing the “DAY” key and the display will change as follows:ġ. When programming ON/OFF events, all days are indicated by default. Note that a total of 7-ON and 7-OFF events can be programmed.ġ. If complete press the “CLOCK” key to return to current time and day.ĥ. When complete press the “PROG” key once.Ĥ. See block programming below for selecting different days of the week. Using the “HOUR” and “MIN” keys enter the desired OFF time. See block programming below for selecting different days of the week.ģ. Using the “HOUR” and “MIN” keys enter the desired ON time. Press the “PROG” key once.TIMER 1 on - : - appears.Ģ. Now the timer is in operation and ready to be programmed.The colon “:” after the hours will continuously flash indicating that the clock is running.ġ. Release the “CLOCK” key once the time and day have been entered. If any keys are pressed for a prolonged period, the display will advance rapidly.Ħ. Press the “DAY” key to advance the day.ĥ. Press the “MIN” key to advance the minutes.Ĥ. Press the “HOUR” key to advance the hours.ģ. Press and HOLD the “CLOCK” key during this entire procedure.Ģ. The display should flash 12:00AM on Monday.ġ. Press the “RESET” button using an insulated tool such as a toothpick.Ĥ. Lift up the bottom of the door using a small slotted screwdriver.ģ. Place wall-plate over timer and screw in to place using screws providedġ. Using the screws provided, mount the timer to the wall box being careful not to crush any wires.ĥ. Tuck the wires into the wall box leaving room for theTimer. Note: Be sure that all wire nuts are secure.Ĥ. Often, the neutral wire can be found in the back of the wiring box bound in a wire nut.Ĭ) Connect the Hot/Live wire of Load to the Red wire fromTimer.ĭ) Connect the Ground wire to the Green wire fromTimer. Connect the wires of Timer and wall box as followed by using the wire nuts provided.Ī) Connect the Hot/Live wire of main power to the Black wire fromTimer.ī) Connect the Neutral wires to the White wire fromTimer. Turn OFF the main power at the circuit breaker.ģ. If you are unsure or unclear about this instalation, contact a qualified licensed electrician.ġ.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |